BEHR PREMIUM® Transparent Waterproofing Wood Finish

Average Rating:
false

Give wood the ultimate in protection with BEHR PREMIUM Transparent Weatherproofing All-In-One Wood Finish. This 100% acrylic formula seals out the elements and the sun's harmful UV rays, for up to 4 yrs. on decks and up to 6 yrs.on fences and siding. It's available in 3 pre-mixed colours as well as 6 custom colours so you can get the look you want while preserving your valuable investment.

See Our Selection of Transparent Wood Finishes.


Finish

Creates a Clear Finish that showcases the full natural beauty of the wood.

Best for use in

New to slightly weathered, unsealed exterior wood surfaces (0-5 years exposure) such as: Decks, Railings, Shakes, Shingles, Siding, Roofs, Fences and Wood Patio Furniture.

Coverage

1st Coat: 28-32 m2 ; 2nd Coat: 56-65 m2


0
PRODUCT USAGE

Must Prep
Before Applying
Wood Stain

2 Thin Coats
Required

1st Coat
28-32 m2
2nd Coat
56-65 m2

Soap & Water
Clean-Up

"For Wood Substrates Only" Recommended for properly prepared new to slightly weathered, unsealed exterior wood surfaces (0-5 years exposure) such as: Decks, Railings, Shakes, Shingles, Siding, Roofs, Fences and Wood Patio Furniture.

Read More

The following steps are recommended for best results.

  • Use a product such as BEHR PREMIUM® NO. 64 Wood Stain & Finish Stripper to remove loose wood fibers, latex, oil-based and 100% acrylic coatings on new or weathered wood.
  • BEHR PREMIUM® NO. 63 All-In-One Wood Cleaner MUST be used following NO. 64 to clean, brighten & neutralize wood.
  • When NO. 64 is not needed, use a product such as NO. 63 to clean and brighten the wood surface and to remove light to medium exterior stains caused by mold, mildew, algae & fungus.
  • On new wood, use a product such as NO. 63 to remove mill glaze and open the pores of the wood. Rinse thoroughly and allow to dry before coating. Lightly sand to remove remaining wood fibers/fuzz.
Read More

For best results, a pad applicator is recommended over large areas.

  • Must apply between 5-32˚ C. Do not use if rain is expected within 24 hours.
  • The wood surface must be completely dry before application.
  • Intermix multiple containers to ensure colour uniformity. DO NOT THIN PRODUCT.
  • Stir product occasionally throughout application. Test product for penetration and colour on a small hidden area before proceeding.
  • Use a nylon/polyester brush for areas requiring more accuracy. Use of rollers should be limited to rough surfaces only. Use 10 mm nap or longer when appropriate.
  • A high quality pump sprayer with a variable tip or an airless sprayer with a .38 mm - .48 mm (.015 - .019") tip may be used.
  • Work in small sections lightly saturating the surface and immediately back-brush or use pad applicator to eliminate puddling, remove excess and evenly distribute the finish. Maintain a wet edge when applying.
  • Apply product end-to-end or to board lengths to prevent lap marks. Over application of finish will lead to surface failure including peeling and cracking.
  • Avoid applying finish too heavily. Two thin coats required.
  • For optimum performance, coat all six sides of wood.
Read More

  • 1-2 hours before recoat. Allow 72 hours for full cure.
Read More

  • For disposal of empty containers and unused product, contact your household refuse collection service.
To consult with a Behr Certified Coatings Professional, call 1-800-661-1591.
Read More

Reviews

How-To

Find step-by-step instructions in our how-to articles and videos.

Often Bought Together
BEHR PREMIUM® All-In-One Wood Cleaner
Learn More
BEHR PREMIUM® Wood Stain & Finish Stripper
Learn More
MSDS AND DATA SHEET

WARRANTY

Behr Process Corporation warrants to you, the original residential consumer purchaser, the performance of this product as described on this label for 6 years on vertical surfaces and 4 years on horizontal surfaces, from the date of purchase. THIS WARRANTY IS NOT VALID WHEN THE PRODUCT IS NOT PROPERLY APPLIED TO A PROPERLY PREPARED SURFACE OR CARED FOR IN ACCORDANCE WITH THE LABEL DIRECTIONS. Colour fading and slight natural graying of the wood may occur during the warranty period, especially in areas exposed to heavy foot traffic or excessive weather. This warranty is not transferable. If this product is found not to perform as specified on the label during the warranty period, Behr Process Corporation will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. The clause of limitation of liability which follows is inapplicable in Québec. This warranty excludes (1) labour and costs of labour for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. The above provisions are not intended to operate where prohibited by law. This limited warranty is the only warranty provided by Behr Process Corporation unless extended by a provincial consumer statute. To obtain warranty service, call 1-800-854-0133 ext. 2, or contact Behr Process Corporation at 2750 Centre Avenue N.E., Calgary, AB T2A2L3. Behr Process Corporation reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.

Never miss out on the hottest deals and latest news from BEHR.

Please enter email address.
Please enter email address.
Water Resistant Coatings